Pulla Bungs & Bungs

Drennan Pull Bung

This clever device enables the angler to adjust the amount of elastic a fish can take from the base end of a top kit. Used sensibly it can enable an angler to effectively use a lighter grade of pole elastic and still be in control of both large and small fish.

The pack comes with two different sizes of toggle bead to accommodate a wide range of solid and hollow elastics.

It also comes fitted with super slick PTFE bushes at both the top and bottom. The tapered cone can be carefully cut back to fit inside your pole section to the appropriate depth.

Features:

• Low diameter toggle bead
• Large diameter toggle bead
• Fitted with super slick PTFE bushes at both the top and bottom
• Tapered cone

​​​

Drennan Puller Beads Aqua

Puller Beads are produced with different diameter central holes to suit a variety of solid and hollow pole elastics and are colour coded to match Drennan bungee colours and diameters.  Manufactured in a semi-flexible polymer, they are designed to hold elastic knots securely in place and also allow adjustments to elastic tension.

The Range:
Blue
Green
Yellow
Pink
Red

Drennan Puller Beads Green

Puller Beads are produced with different diameter central holes to suit a variety of solid and hollow pole elastics and are colour coded to match Drennan bungee colours and diameters.  Manufactured in a semi-flexible polymer, they are designed to hold elastic knots securely in place and also allow adjustments to elastic tension.

The Range:
Blue
Green
Yellow
Pink
Red

Drennan Puller Beads Pink

Puller Beads are produced with different diameter central holes to suit a variety of solid and hollow pole elastics and are colour coded to match Drennan bungee colours and diameters.  Manufactured in a semi-flexible polymer, they are designed to hold elastic knots securely in place and also allow adjustments to elastic tension.

The Range:
Blue
Green
Yellow
Pink
Red

Drennan Puller Beads Red

Puller Beads are produced with different diameter central holes to suit a variety of solid and hollow pole elastics and are colour coded to match Drennan bungee colours and diameters.  Manufactured in a semi-flexible polymer, they are designed to hold elastic knots securely in place and also allow adjustments to elastic tension.

The Range:
Blue
Green
Yellow
Pink
Red

Drennan Puller Beads Yellow

Puller Beads are produced with different diameter central holes to suit a variety of solid and hollow pole elastics and are colour coded to match Drennan bungee colours and diameters.  Manufactured in a semi-flexible polymer, they are designed to hold elastic knots securely in place and also allow adjustments to elastic tension.

The Range:
Blue
Green
Yellow
Pink
Red

Drennan Winder Bungs Large

Each Winder Bung will hold numerous turns of elastic, allowing small lengths to be let out or wound in and precise adjustments to be made to the tension of your pole elastic. The Medium and Large sizes will even hold several turns of larger diameter Drennan Carp Bungee hollow elastic.

The winder section has a dovetail joint, which allows it to be separated from the tapered bung and reassembled with ease if necessary. The tapered cone section also has a small drainage channel in each side to prevent water becoming trapped inside the top sections.

The tapered cones on the four sizes of bung each have a ribbed section which can be cut down with a sharp knife or junior hacksaw. This simple modification gives each size a maximum and minimum diameter. The range can therefore be made to fit all pole sections and top kits with an internal bore between 10mm and 30mm.

These ultra light Winder Bungs weigh so little that they will have minimal effect on the balance or action of your pole.

On standard take-apart poles the Winder Bung needs to fit inside the section, just beyond joint depth and within easy reach of the extractor rod. The extractor rod has a positive twist-lock location system so it is very easy to remove a Winder Bung from its position inside the pole section.

As these two-part winders can be separated from the bung section it makes them interchangeable, providing an increased range of storage options and therefore further scope for tension adjustments to the pole elastic.

All pole elastic is prone to damage and wear, particularly at the tip end where the rig line or connector is attached. Having spare elastic on the winder not only allows you to adjust the tension but also to periodically cut back the elastic, eliminating the worn tip section.

Features:

• Winder section has a dovetail joint
• Tapered cone section
• Ultra light
• Ribbed sections which can be cut down with a sharp knife or junior hacksaw
• Two-part winders can be separated from the bung section it makes them interchangeable

Storage Capacity:

• Mini holds up to 15 turns of No4 elastic - 18″ (45cm)
• Small holds up to 12 turns of No6 elastic - 24″ (60cm)
• Medium holds up to 20 turns of No10 elastic - 44″ (112cm)
• Large holds up to 8 turns of No14 elastic - 32″ (80cm)

The Range:

• Mini -  Pink, 0.9g, three per pack (10mm to 12mm)
• Small - Green, 1.7g, three per pack (12.5mm to 15mm)
• Medium - Blue, 2.5g, two per pack (15.5mm to 20mm)
• Large - Purple, 4.5g, 2 per pack (21.5mm to 30mm)

Drennan Winder Bungs Medium

Each Winder Bung will hold numerous turns of elastic, allowing small lengths to be let out or wound in and precise adjustments to be made to the tension of your pole elastic. The Medium and Large sizes will even hold several turns of larger diameter Drennan Carp Bungee hollow elastic.

The winder section has a dovetail joint, which allows it to be separated from the tapered bung and reassembled with ease if necessary. The tapered cone section also has a small drainage channel in each side to prevent water becoming trapped inside the top sections.

The tapered cones on the four sizes of bung each have a ribbed section which can be cut down with a sharp knife or junior hacksaw. This simple modification gives each size a maximum and minimum diameter. The range can therefore be made to fit all pole sections and top kits with an internal bore between 10mm and 30mm.

These ultra light Winder Bungs weigh so little that they will have minimal effect on the balance or action of your pole.

On standard take-apart poles the Winder Bung needs to fit inside the section, just beyond joint depth and within easy reach of the extractor rod. The extractor rod has a positive twist-lock location system so it is very easy to remove a Winder Bung from its position inside the pole section.

As these two-part winders can be separated from the bung section it makes them interchangeable, providing an increased range of storage options and therefore further scope for tension adjustments to the pole elastic.

All pole elastic is prone to damage and wear, particularly at the tip end where the rig line or connector is attached. Having spare elastic on the winder not only allows you to adjust the tension but also to periodically cut back the elastic, eliminating the worn tip section.

Features:

• Winder section has a dovetail joint
• Tapered cone section
• Ultra light
• Ribbed sections which can be cut down with a sharp knife or junior hacksaw
• Two-part winders can be separated from the bung section it makes them interchangeable

Storage Capacity:

• Mini holds up to 15 turns of No4 elastic - 18″ (45cm)
• Small holds up to 12 turns of No6 elastic - 24″ (60cm)
• Medium holds up to 20 turns of No10 elastic - 44″ (112cm)
• Large holds up to 8 turns of No14 elastic - 32″ (80cm)

The Range:

• Mini -  Pink, 0.9g, three per pack (10mm to 12mm)
• Small - Green, 1.7g, three per pack (12.5mm to 15mm)
• Medium - Blue, 2.5g, two per pack (15.5mm to 20mm)
• Large - Purple, 4.5g, 2 per pack (21.5mm to 30mm)

Drennan Winder Bungs Mini

Each Winder Bung will hold numerous turns of elastic, allowing small lengths to be let out or wound in and precise adjustments to be made to the tension of your pole elastic. The Medium and Large sizes will even hold several turns of larger diameter Drennan Carp Bungee hollow elastic.

The winder section has a dovetail joint, which allows it to be separated from the tapered bung and reassembled with ease if necessary. The tapered cone section also has a small drainage channel in each side to prevent water becoming trapped inside the top sections.

The tapered cones on the four sizes of bung each have a ribbed section which can be cut down with a sharp knife or junior hacksaw. This simple modification gives each size a maximum and minimum diameter. The range can therefore be made to fit all pole sections and top kits with an internal bore between 10mm and 30mm.

These ultra light Winder Bungs weigh so little that they will have minimal effect on the balance or action of your pole.

On standard take-apart poles the Winder Bung needs to fit inside the section, just beyond joint depth and within easy reach of the extractor rod. The extractor rod has a positive twist-lock location system so it is very easy to remove a Winder Bung from its position inside the pole section.

As these two-part winders can be separated from the bung section it makes them interchangeable, providing an increased range of storage options and therefore further scope for tension adjustments to the pole elastic.

All pole elastic is prone to damage and wear, particularly at the tip end where the rig line or connector is attached. Having spare elastic on the winder not only allows you to adjust the tension but also to periodically cut back the elastic, eliminating the worn tip section.

Features:

• Winder section has a dovetail joint
• Tapered cone section
• Ultra light
• Ribbed sections which can be cut down with a sharp knife or junior hacksaw
• Two-part winders can be separated from the bung section it makes them interchangeable

Storage Capacity:

• Mini holds up to 15 turns of No4 elastic - 18″ (45cm)
• Small holds up to 12 turns of No6 elastic - 24″ (60cm)
• Medium holds up to 20 turns of No10 elastic - 44″ (112cm)
• Large holds up to 8 turns of No14 elastic - 32″ (80cm)

The Range:

• Mini -  Pink, 0.9g, three per pack (10mm to 12mm)
• Small - Green, 1.7g, three per pack (12.5mm to 15mm)
• Medium - Blue, 2.5g, two per pack (15.5mm to 20mm)
• Large - Purple, 4.5g, 2 per pack (21.5mm to 30mm)

Drennan Winder Bungs Small

Each Winder Bung will hold numerous turns of elastic, allowing small lengths to be let out or wound in and precise adjustments to be made to the tension of your pole elastic. The Medium and Large sizes will even hold several turns of larger diameter Drennan Carp Bungee hollow elastic.

The winder section has a dovetail joint, which allows it to be separated from the tapered bung and reassembled with ease if necessary. The tapered cone section also has a small drainage channel in each side to prevent water becoming trapped inside the top sections.

The tapered cones on the four sizes of bung each have a ribbed section which can be cut down with a sharp knife or junior hacksaw. This simple modification gives each size a maximum and minimum diameter. The range can therefore be made to fit all pole sections and top kits with an internal bore between 10mm and 30mm.

These ultra light Winder Bungs weigh so little that they will have minimal effect on the balance or action of your pole.

On standard take-apart poles the Winder Bung needs to fit inside the section, just beyond joint depth and within easy reach of the extractor rod. The extractor rod has a positive twist-lock location system so it is very easy to remove a Winder Bung from its position inside the pole section.

As these two-part winders can be separated from the bung section it makes them interchangeable, providing an increased range of storage options and therefore further scope for tension adjustments to the pole elastic.

All pole elastic is prone to damage and wear, particularly at the tip end where the rig line or connector is attached. Having spare elastic on the winder not only allows you to adjust the tension but also to periodically cut back the elastic, eliminating the worn tip section.

Features:

• Winder section has a dovetail joint
• Tapered cone section
• Ultra light
• Ribbed sections which can be cut down with a sharp knife or junior hacksaw
• Two-part winders can be separated from the bung section it makes them interchangeable

Storage Capacity:

• Mini holds up to 15 turns of No4 elastic - 18″ (45cm)
• Small holds up to 12 turns of No6 elastic - 24″ (60cm)
• Medium holds up to 20 turns of No10 elastic - 44″ (112cm)
• Large holds up to 8 turns of No14 elastic - 32″ (80cm)

The Range:

• Mini -  Pink, 0.9g, three per pack (10mm to 12mm)
• Small - Green, 1.7g, three per pack (12.5mm to 15mm)
• Medium - Blue, 2.5g, two per pack (15.5mm to 20mm)
• Large - Purple, 4.5g, 2 per pack (21.5mm to 30mm)

Preston Bung & Extractor Kit Large

Ribbed base for ease of cutting
Elastic holder to optimise elastic tension
Easy to remove design
Extractor rod supplied

Preston Bung & Extractor Kit Medium

Ribbed base for ease of cutting
Elastic holder to optimise elastic tension
Easy to remove design
Extractor rod supplied

Preston Bung & Extractor Kit Small

Ribbed base for ease of cutting
Elastic holder to optimise elastic tension
Easy to remove design
Extractor rod supplied

Preston Pulla Bung

Met de Preston Pulla Bung bent u in staat om het elastiek strakker te trekken nadat de topset is los gehaald. Zo kunt u lichter elastiek gebruiken en hoeft u sterke vis niet meer met het 5e of zelfs 6e deel af te drillen.

Preston Pulla Bung Connector Beads

The Preston Innovations Pulla Bung Spare Beads are replacement connector beads for Pulla Kits. The Pulla Bung Spare Beads are supplied per 10 pieces.

Preston Stora Bung Twin Kit Large

Ribbed base for ease of cutting
Elastic holder for optimum tension
Easy to remove design (Extractor rod required)
Supplied in packs of two
21mm

Preston Stora Bung Twin Kit Medium

Ribbed base for ease of cutting
Elastic holder for optimum tension
Easy to remove design (Extractor rod required)
Supplied in packs of two
21mm

Preston Stora Bung Twin Kit Small

Ribbed base for ease of cutting
Elastic holder for optimum tension
Easy to remove design (Extractor rod required)
Supplied in packs of two
13mm